1) Super Server 6023P-8R ; Xeon Motherboard X5DP8-G2; чипсет Intel E7501
2) контроллер Adaptec AIC-7902A4;
3) MegaRaid SCSI 320-2
4) Xyratex SCSI RAID RR-1422-LVD-JBD
Проблема:
Собственно, никаких проблем, пока не пытаемся повесить на MegaRaid внутреннюю корзину. Полгода назад была сделана такая попытка ? при этом начинает виснуть GAM, а Power Console Plus непрерывно сыпет сообщениями типа:
Код: Выделить всё
Enclosure Alert on Channel 0 - Mon Aug 01 19:39:28 2005
*********************************************
NVRAM EVENT LOG :
LOG -1431655201 EVENT 0x200 TIME 08/01/2021 17:10:24
Channel 0, Target 0, Lun 0
Code: 0x200
Category: Physical Device Error Event.
Sense Data: 0x00 0x00 0x09 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x83 0x00 0x00
0x00 0x00 0x00
CDB: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Текущее положение джамперов и свичей:
Код: Выделить всё
Устройство Джамперы/переключатели Положение
Supermicro JP22 1-2 (Enable) ?
JPA1 Open (Enable)
JPA2 Open (Enable)
MegaRAID 320-2 J4 No jumpers
J5 1-2 ?
J17 jumpered
J18 jumpered
Xyratex Force High Address Range off
Disable Termination Expansion off
Disable Termination Host off
Диски Seagate ST373307LC default (No jumpers)
Код: Выделить всё
JP22
allows you to enable or disable the onboard SCSI controller. The normal (default) position is on pins 1-2 to enable SCSI termination
JPA1 JPA2
allow you to enable or disable termination for the individual SCSI channels. Jumper JPA1 controls SCSI channel A and JPA2 - channel B. The normal (default) setting is open to enable (teminate) both SCSI channels. If you wish to connect external SCSI devices, you should disable termination for the channnel(s) you will be connecting them to.
J4 J5
SCSI Termination Enable
J4 - Channel 0, J5 - Channel 1.
No jumper: On-board SCSI termination enabled. (Refer to J17 and J18.) This is the default. Note: Leave J4 and J5 at the default setting to allow the MegaRAID SCSI 320-2 to automatically set its own SCSI termination.
Jumper on pins 1?2: Software uses drive detection to control SCSI termination.
Jumper on pins 2?3: On-board SCSI termination disabled.
J17 J18
Termination Power Enable Channel 0 (J17), Channel 1(J18)
Jumpered: TERMPWR is enabled from the PCI bus. (default)
No jumper: TERMPWR is enabled from the SCSI bus. (Refer to J4 and J5)
А для Xyratex есть только картинка с названиями, а описания переключателей нет:
Force High Address Range
Disable Termination Expansion
Disable Termination Host
А может, кто подскажет, как работают переключатели на Xyratex