Перепрошивка фирмваря?
Модераторы: Trinity admin`s, Free-lance moderator`s
Перепрошивка фирмваря?
Есть (был?) LSI MegaRAID SCSI 320-1, BBU нет
Поставил в обычный PCI-слот, 2 винта ST373207LW
При входе в WEB-менежер было видно и контроллер и винты, после попытки ткнуть куда-нибудь мышкой - система зависает намертво
Загрузил DOS, запустил MFLASH.exe, поставил фирмварь 1L37 взамен (кажется ) 1L13
Прога отработала нормально, в конце ".... succsessful" и "reboot to continue"
Теперь при включении системы на контроллере сразу загорается красненькая лампочка, и в системе контроллер не проявляет своего присутствия. Перемычку на CLEAR EPROM одевал-снимал.
Неужели сдох? И если нет, то что сделать, чтоб оживить
Поставил в обычный PCI-слот, 2 винта ST373207LW
При входе в WEB-менежер было видно и контроллер и винты, после попытки ткнуть куда-нибудь мышкой - система зависает намертво
Загрузил DOS, запустил MFLASH.exe, поставил фирмварь 1L37 взамен (кажется ) 1L13
Прога отработала нормально, в конце ".... succsessful" и "reboot to continue"
Теперь при включении системы на контроллере сразу загорается красненькая лампочка, и в системе контроллер не проявляет своего присутствия. Перемычку на CLEAR EPROM одевал-снимал.
Неужели сдох? И если нет, то что сделать, чтоб оживить
Переставлял не только по слотам, но и на 3-х разных МВ пробовал -эффект одинаков: сразу после включения светит красным фонарем диодик. А на ASUS P4P800-E еще и канал IDE пропадает. Перепрошивка биоса на гарантийных обязательствах скажется, или это по усмотрению фирмы-продавца?
В слоте PCI контроллеру может "плохо" житься? По документации вроде можно спокойно ставить
А нет ли какой проги, чтоб "насильно" его перепрошить еще раз? А то обычный MFLASH.EXE говорит "NO PCI-adapter installed"
В слоте PCI контроллеру может "плохо" житься? По документации вроде можно спокойно ставить
А нет ли какой проги, чтоб "насильно" его перепрошить еще раз? А то обычный MFLASH.EXE говорит "NO PCI-adapter installed"
Ключики у mflash следующие:
/9060 : Flash the 434-Series Controller Card.
/s : Flash without asking for user input to flash adapter(s).
/p : Prompt user for filename. Flash without checking for ignatures
/i : Ignore the following files. These files will not be considered for flashing the matching controllers
/f : Force the following files to be flashed for the matching controller
In case more than one matching files are specified, the first one wold be taken
/b : Flash through the BOOT Block. Should be used only if the F/W gets
corrupted and BOOT Block can repair the F/W by flashing the new
F/W that is specified. This is valid for the controllers which
support Flashing through BOOT Block, namely the 40 LD controllers.
/a[n] : Flash the controller at index [n]
/v[xxxx] : Flash the controller if the current FirmWare Level is below [xxxx]
/xml : Place output in XML format
/q : Query all adapters. Display card type, current BIOS and F/W version
с ключиком /b - No Adapter with a corrupted F/W Found
c другими - Adapter not Found
Может кто знает, на какую перемычку ему 380В подать, чтоб проснулся?
/9060 : Flash the 434-Series Controller Card.
/s : Flash without asking for user input to flash adapter(s).
/p : Prompt user for filename. Flash without checking for ignatures
/i : Ignore the following files. These files will not be considered for flashing the matching controllers
/f : Force the following files to be flashed for the matching controller
In case more than one matching files are specified, the first one wold be taken
/b : Flash through the BOOT Block. Should be used only if the F/W gets
corrupted and BOOT Block can repair the F/W by flashing the new
F/W that is specified. This is valid for the controllers which
support Flashing through BOOT Block, namely the 40 LD controllers.
/a[n] : Flash the controller at index [n]
/v[xxxx] : Flash the controller if the current FirmWare Level is below [xxxx]
/xml : Place output in XML format
/q : Query all adapters. Display card type, current BIOS and F/W version
с ключиком /b - No Adapter with a corrupted F/W Found
c другими - Adapter not Found
Может кто знает, на какую перемычку ему 380В подать, чтоб проснулся?
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 14 гостей