Коммутаторы Сisco Catalyst 2950
Модераторы: Trinity admin`s, Free-lance moderator`s
-
- Power member
- Сообщения: 48
- Зарегистрирован: 17 фев 2006, 22:55
- Откуда: Тамбов
- Контактная информация:
Коммутаторы Сisco Catalyst 2950
Если кратко - соединяем патч-кордом два коммутатора через порты Fast Ethernet - работает, через Gigabit Ethernet - ни в какую! Подозрение возникает, что так их соединять нельзя? А как?
-
- Power member
- Сообщения: 48
- Зарегистрирован: 17 фев 2006, 22:55
- Откуда: Тамбов
- Контактная информация:
GigabitEthernet0/2 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 0015.f9d5.3372 (bia 0015.f9d5.3372)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, media type is RJ45
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 04:02:55, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1 packets input, 64 bytes, 0 no buffer
Received 0 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
1 packets output, 64 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Hardware is Gigabit Ethernet, address is 0015.f9d5.3372 (bia 0015.f9d5.3372)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, media type is RJ45
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 04:02:55, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
1 packets input, 64 bytes, 0 no buffer
Received 0 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
1 packets output, 64 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Хорошо бы видеть это с обоих сторон;)
Что бы как-то оправдать это действие;)
Interface GigabitEthernet0/2 (down/down (notconnect))
WARNING: The neighboring device is administratively down.
TRY THIS: Issue the 'no shutdown' on the interface of the neighboring device to
enable it. Ensure that line speed and duplex are the same at both ends.
INFO: The CRC erros found on the interface are less than 0.0001% of the total
input packets and can be ignored.
WARNING: There have been 2 'interface resets' reported.
This can happen if packets queued for transmission were not sent within several
seconds. Interface resets can also occur when an interface is looped back or
shutdown.
TRY THIS: Monitor the level of interface resets over time. If they are increasing,
this could be a symptom of a hardware or configuration issue. Try swapping interfaces
and or ports to identify the problem.
От себя могу добавить - опустите скорость на обоих до 100 и посмотрите или воткните гиг порт в фаст
Что бы как-то оправдать это действие;)
Interface GigabitEthernet0/2 (down/down (notconnect))
WARNING: The neighboring device is administratively down.
TRY THIS: Issue the 'no shutdown' on the interface of the neighboring device to
enable it. Ensure that line speed and duplex are the same at both ends.
INFO: The CRC erros found on the interface are less than 0.0001% of the total
input packets and can be ignored.
WARNING: There have been 2 'interface resets' reported.
This can happen if packets queued for transmission were not sent within several
seconds. Interface resets can also occur when an interface is looped back or
shutdown.
TRY THIS: Monitor the level of interface resets over time. If they are increasing,
this could be a symptom of a hardware or configuration issue. Try swapping interfaces
and or ports to identify the problem.
От себя могу добавить - опустите скорость на обоих до 100 и посмотрите или воткните гиг порт в фаст
-
- Power member
- Сообщения: 48
- Зарегистрирован: 17 фев 2006, 22:55
- Откуда: Тамбов
- Контактная информация:
В данный момент коммутаторы соединены патч-кордом через порты Fast Ethernet. Как я понял нужно соединить их патч-кордом через гигабитные порты и сделать show interface... ?
Я пробовал 4 варианта соединения:
1) Fast - Fast - работает
2) Gigabit - Fast - работает
3) Fast - Gigabit - работает
4) Gigabit - Gigabit - не работает
Подключал гигабитный порт к гигабитному порту коммутатора TrendNet - тоже все ок :)
Модель коммутаторов WS-C2950T-48-SI
Я пробовал 4 варианта соединения:
1) Fast - Fast - работает
2) Gigabit - Fast - работает
3) Fast - Gigabit - работает
4) Gigabit - Gigabit - не работает
Подключал гигабитный порт к гигабитному порту коммутатора TrendNet - тоже все ок :)
Модель коммутаторов WS-C2950T-48-SI
Попробуйте данный кроссовер кабель
http://www.cisco.com/en/US/partner/tech ... 4781.shtml
Сразу предупреждаю, что сам занимался этим во время плясок с бубном и при том зоопарке на стенде положительной динамики от данного кабеля не заметил.
http://www.cisco.com/en/US/partner/tech ... 4781.shtml
Сразу предупреждаю, что сам занимался этим во время плясок с бубном и при том зоопарке на стенде положительной динамики от данного кабеля не заметил.
http://www.cisco.com/en/US/products/hw/ ... #wp1020356
Схема Switch - Switch.
Если не работает, то сбросьте на обоих коммутаторах порты в дефолтные настройки, так же попробуйте другой кабель.
Обращаю внимание, что для гигабитных портов при ГИГАБИТНОМ соединении через кроссоверный кабель надо перекидывать не только контакты 1 2 и 3 6 (этого достаточно для Fast Ethernet), к но и 4 5 и 7 8
Дело в том, что в Гигабите используются все пары, а не две, как в Fast Ethernet.
Схема Switch - Switch.
Если не работает, то сбросьте на обоих коммутаторах порты в дефолтные настройки, так же попробуйте другой кабель.
Обращаю внимание, что для гигабитных портов при ГИГАБИТНОМ соединении через кроссоверный кабель надо перекидывать не только контакты 1 2 и 3 6 (этого достаточно для Fast Ethernet), к но и 4 5 и 7 8
Дело в том, что в Гигабите используются все пары, а не две, как в Fast Ethernet.
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 1 гость