После прочистки от пыли, произошло нечто. Перестала загружаться IOS
Вот что пишет
Cisco Internetwork Operating System Software
IOS (tm) EGR Software (UBR7100-IK1S-M), Version 12.1(12c)EC1, EARLY DEPLOYMENT R
ELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 19-Jul-02 11:48 by yiyan
Image text-base: 0x60008950, data-base: 0x618B0000
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
R5K CPU
ROM: Rebooted by watchdog hard reset
C7100 platform with 131072 Kbytes of main memory
Read cis from dev 0 error (-7)device does not contain a valid magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "cisco2-C7100"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
R5K CPU
C7100 platform with 131072 Kbytes of main memory
string is disk0:ubr7100-ik1s-mz.121-12c.EC1.bin
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
############################################################# [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
И так по кругу.....
С Flash читает данные.
Где собака порылась??
Не загружается IOS CISCO UBR7114
Модераторы: Trinity admin`s, Free-lance moderator`s
Если после чистки, то скорее всего аппаратное.
Для начала, попробуй загрузиться в rommon
http://www.cisco.com/en/US/customer/pro ... 87230.html
Посмотри память, устройства, файлы.
Посмотри регистр и настрой,если надо.
Попробуй загрузиться с другого места (tftp?) без конфига.
Для начала, попробуй загрузиться в rommon
http://www.cisco.com/en/US/customer/pro ... 87230.html
Посмотри память, устройства, файлы.
Посмотри регистр и настрой,если надо.
Попробуй загрузиться с другого места (tftp?) без конфига.
В rommon загружается.
Ссылка которую дали -требует пароля
Память ОК
Устройства ОК
Файлы ОК
Вытащил SIMM (bootflash) -пытался загрузиться с карты -не хочет.
Делал confreg -без изменений.
Однако возможно я то то не так делал. Я не спец блиг в этом.
Всё по книге делал.
С tftp не загружался. Разве из rommon можно?
Ссылка которую дали -требует пароля
Память ОК
Устройства ОК
Файлы ОК
Вытащил SIMM (bootflash) -пытался загрузиться с карты -не хочет.
Делал confreg -без изменений.
Однако возможно я то то не так делал. Я не спец блиг в этом.
Всё по книге делал.
С tftp не загружался. Разве из rommon можно?
Показать регистр -что за комманда? я не знаю как
rommon 1 > meminfo
Main memory size: 128 MB.
Shared memory size: 64 MB
Main memory size: 0x8000000
Available main memory starts at 0xa000e000, size 0x7ff2000
NVRAM size: 0x20000
Parity Map for the DRAM Banks
rommon 2 > dev
Devices in device table:
id name
bootflash: boot flash
slot0: PCMCIA slot 0
slot1: PCMCIA slot 1
disk0: PCMCIA slot 0
disk1: PCMCIA slot 1
eprom: eprom
rommon 4 > dir slot1:
Directory of slot1:
3 10066152 -rw- ubr7100-ik1s-mz.121-12c.EC1.bin
2461 76 -rw- platinum.cm
2462 74 -rw- silver.cm
2463 74 -rw- bronze.cm
2464 74 -rw- gold.cm
2465 118 -rw- bpiuxcpe2.cm
2466 4004 -rw- konturm
2467 118 -rw- bpiuxcpe1.cm
2468 118 -rw- bpicpe1.cm
2469 120 -rw- bpiu3cpe2.cm
2470 120 -rw- bpiu3cpe1.cm
2471 120 -rw- bpiu2cpe2.cm
2472 120 -rw- bpiu2cpe1.cm
2473 120 -rw- bpiu1cpe2.cm
2474 120 -rw- bpiu1cpe1.cm
2475 120 -rw- bpiu0cpe2.cm
2476 120 -rw- bpiu0cpe1.cm
И так, может пригодиться!!!!
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
string is disk0:ubr7100-ik1s-mz.121-12c.EC1.bin
Stack pointer : 0x87FFFF80
monstack : 0x80007FC0
monra : 0xBFC0175C
edata : 0x8000E3E0
magic : 0xFEEDFACE
memsize : 0x08000000
uncomp_size : 0x019CAEDC
comp_size : 0x009933FD
comp_checksum : 0xA3BE7B78
uncomp_checksum : 0x5608277B
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
############################################################# [OK]
Source elf_hdr->e_shnum = 0x00000008
Setting up to copy ELF section 0x00000001
to image_info section 0x00000000
sh_name = 0x0000001B
sh_type = 0x00000001
sh_flags = 0x00000006
sh_addr = 0x80008000
sh_offset = 0x00000080
sh_size = 0x018A8000
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000040
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000002
to image_info section 0x00000001
sh_name = 0x00000021
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x818B0000
sh_offset = 0x018A8080
sh_size = 0x00120C00
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000008
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000003
to image_info section 0x00000002
sh_name = 0x00000027
sh_type = 0x00000001
sh_flags = 0x10000003
sh_addr = 0x819D0C00
sh_offset = 0x019C8C80
sh_size = 0x000020C0
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000010
sh_entsize = 0x00000000
cpu type : 0x00000044
uncomp_size : 0x019CAEDC
monstack : 0x80007FC0
image_info.entry_point = 0x80008000
image_info.section_count = 0x00000003
image_info.monstack = 0x80007FC0
image_info.monra = 0xBFC0175C
image_info.param0 = 0x00000002
image_info.param1 = 0x00000000
image_info.param2 = 0x80005458
image_info.param3 = 0x80008000
Section Index = 0x00000000
source = 0x80036A00
dest = 0x80008000
bytes = 0x018A8000
Section Index = 0x00000001
source = 0x818DEA00
dest = 0x818B0000
bytes = 0x00120C00
Section Index = 0x00000002
source = 0x819FF600
dest = 0x819D0C00
bytes = 0x000020C0
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) EGR Software (UBR7100-IK1S-M), Version 12.1(12c)EC1, EARLY DEPLOYMENT R
ELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 19-Jul-02 11:48 by yiyan
Image text-base: 0x60008950, data-base: 0x618B0000
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
ROM: Rebooted by watchdog hard reset
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "cisco2-C7100"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
string is disk0:ubr7100-ik1s-mz.121-12c.EC1.bin
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "cisco2-C7100"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
Read cis from dev 0 error (-6)PCMCIA slot0 device is not initialized
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "slot0:"
boot: cannot determine first file name on device "slot0:"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
boot: cannot determine first file name on device "bootflash:"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
rommon 1 > meminfo
Main memory size: 128 MB.
Shared memory size: 64 MB
Main memory size: 0x8000000
Available main memory starts at 0xa000e000, size 0x7ff2000
NVRAM size: 0x20000
Parity Map for the DRAM Banks
rommon 2 > dev
Devices in device table:
id name
bootflash: boot flash
slot0: PCMCIA slot 0
slot1: PCMCIA slot 1
disk0: PCMCIA slot 0
disk1: PCMCIA slot 1
eprom: eprom
rommon 4 > dir slot1:
Directory of slot1:
3 10066152 -rw- ubr7100-ik1s-mz.121-12c.EC1.bin
2461 76 -rw- platinum.cm
2462 74 -rw- silver.cm
2463 74 -rw- bronze.cm
2464 74 -rw- gold.cm
2465 118 -rw- bpiuxcpe2.cm
2466 4004 -rw- konturm
2467 118 -rw- bpiuxcpe1.cm
2468 118 -rw- bpicpe1.cm
2469 120 -rw- bpiu3cpe2.cm
2470 120 -rw- bpiu3cpe1.cm
2471 120 -rw- bpiu2cpe2.cm
2472 120 -rw- bpiu2cpe1.cm
2473 120 -rw- bpiu1cpe2.cm
2474 120 -rw- bpiu1cpe1.cm
2475 120 -rw- bpiu0cpe2.cm
2476 120 -rw- bpiu0cpe1.cm
И так, может пригодиться!!!!
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
string is disk0:ubr7100-ik1s-mz.121-12c.EC1.bin
Stack pointer : 0x87FFFF80
monstack : 0x80007FC0
monra : 0xBFC0175C
edata : 0x8000E3E0
magic : 0xFEEDFACE
memsize : 0x08000000
uncomp_size : 0x019CAEDC
comp_size : 0x009933FD
comp_checksum : 0xA3BE7B78
uncomp_checksum : 0x5608277B
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
############################################################# [OK]
Source elf_hdr->e_shnum = 0x00000008
Setting up to copy ELF section 0x00000001
to image_info section 0x00000000
sh_name = 0x0000001B
sh_type = 0x00000001
sh_flags = 0x00000006
sh_addr = 0x80008000
sh_offset = 0x00000080
sh_size = 0x018A8000
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000040
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000002
to image_info section 0x00000001
sh_name = 0x00000021
sh_type = 0x00000001
sh_flags = 0x00000003
sh_addr = 0x818B0000
sh_offset = 0x018A8080
sh_size = 0x00120C00
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000008
sh_entsize = 0x00000000
Setting up to copy ELF section 0x00000003
to image_info section 0x00000002
sh_name = 0x00000027
sh_type = 0x00000001
sh_flags = 0x10000003
sh_addr = 0x819D0C00
sh_offset = 0x019C8C80
sh_size = 0x000020C0
sh_link = 0x00000000
sh_info = 0x00000000
sh_addralign = 0x00000010
sh_entsize = 0x00000000
cpu type : 0x00000044
uncomp_size : 0x019CAEDC
monstack : 0x80007FC0
image_info.entry_point = 0x80008000
image_info.section_count = 0x00000003
image_info.monstack = 0x80007FC0
image_info.monra = 0xBFC0175C
image_info.param0 = 0x00000002
image_info.param1 = 0x00000000
image_info.param2 = 0x80005458
image_info.param3 = 0x80008000
Section Index = 0x00000000
source = 0x80036A00
dest = 0x80008000
bytes = 0x018A8000
Section Index = 0x00000001
source = 0x818DEA00
dest = 0x818B0000
bytes = 0x00120C00
Section Index = 0x00000002
source = 0x819FF600
dest = 0x819D0C00
bytes = 0x000020C0
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) EGR Software (UBR7100-IK1S-M), Version 12.1(12c)EC1, EARLY DEPLOYMENT R
ELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 19-Jul-02 11:48 by yiyan
Image text-base: 0x60008950, data-base: 0x618B0000
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
ROM: Rebooted by watchdog hard reset
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "cisco2-C7100"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
string is disk0:ubr7100-ik1s-mz.121-12c.EC1.bin
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "cisco2-C7100"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
Read cis from dev 0 error (-6)PCMCIA slot0 device is not initialized
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "slot0:"
boot: cannot determine first file name on device "slot0:"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
boot: cannot determine first file name on device "bootflash:"
System Bootstrap, Version 12.0(5r)XE2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
Testing lower main memory - inverse checkerboard
Clearing lower 16K memory for cache initialization
Clearing bss
Reading monitor variables from NVRAM
Enabling interrupts
Initializing TLB
Initializing cache
Initializing R5K L2 cache
R5K CPU
Initializing required TLB entries
Initializing PCI subsystem
Initializing main memory
Config SDRAM parity check
Initializing shared memory
Sizing NVRAM
Initializing PCMCIA controller
Exiting init
C7100 platform with 131072 Kbytes of main memory
rommon 7 > boot
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
boot: cannot determine first file name on device "bootflash:"
rommon 8 > boot flash
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "flash"
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
boot: cannot determine first file name on device "bootflash:"
rommon 8 > boot flash
getdevnum warning: device "boot flash" has size of zero
getdevnum warning: device "boot flash" has size of zero
open: read error...requested 0x4 bytes, got 0xffffffff
trouble reading device magic number
boot: cannot open "bootflash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "flash"
В ручную пробывал загрузиться с флешки из слота 0 -нифига, сново перегружается.
Я не знаю, проходит в ручную boot или нет. Как узнать?
Единственное что могу сказать, что я могу попасть в rommon либо держать reset 5-6 сек. Либо вытащить из слота 0 карточку. В остальных случаях, идет постоянная перезагрузка.
Я не знаю, проходит в ручную boot или нет. Как узнать?
Единственное что могу сказать, что я могу попасть в rommon либо держать reset 5-6 сек. Либо вытащить из слота 0 карточку. В остальных случаях, идет постоянная перезагрузка.
Отключал из rommon обращение к конфиг... ничего не изменилось.
SDRAM не менял. А если его не в тот слот засунули? Это не повлияет? Там два слота....
И вопрос сразу. SDRAM обычным компьютерный??? В запасах где то валяется планка...
Т.е. можно просто поменять???
Не знаю про резервный имидж.... поищу... а если нету, как быть?
SDRAM не менял. А если его не в тот слот засунули? Это не повлияет? Там два слота....
И вопрос сразу. SDRAM обычным компьютерный??? В запасах где то валяется планка...
Т.е. можно просто поменять???
Не знаю про резервный имидж.... поищу... а если нету, как быть?
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 4 гостя