Что за ошибка?
Модераторы: Trinity admin`s, Free-lance moderator`s
Что за ошибка?
Доброго всем времени суток!Имею скромный сервер на мат плате SE7520JR2.При запуске диагностики выскакивает Error (84FF):System event log full, и на панели индикаторов горит красная лампочка критической ошибки.У меня вопрос с чем это может быть связано?И можно ли исправить это самому?Не прибегая к помощи сервисного центра(гарантия была утеряна).Хочу предупредить что ранее мною была обновлена утилита FRUSDR в связи с тем что все 4 вертушки обдуваемые нутро корпуса очень сильно шумели.
- Tert
- Advanced member
- Сообщения: 4233
- Зарегистрирован: 19 янв 2003, 08:09
- Откуда: Москва
- Контактная информация:
strog2
Сообщение "Error (84FF):System event log full" - это стандартная проблема на всех материнских платах Intel с контроллером mBMC. Под лог в этом контроллере отводится всего 92 записи, которые быстро заполняются (очистить лог можно из BIOS'а платы). С желтой лампочкой на корпусе это сообщение не связано.
Чтобы выяснить в чем проблема, сохраните System Log на дискету и покажите его здесь.
Сообщение "Error (84FF):System event log full" - это стандартная проблема на всех материнских платах Intel с контроллером mBMC. Под лог в этом контроллере отводится всего 92 записи, которые быстро заполняются (очистить лог можно из BIOS'а платы). С желтой лампочкой на корпусе это сообщение не связано.
Чтобы выяснить в чем проблема, сохраните System Log на дискету и покажите его здесь.
Здравствуйте ещё раз!Большое спасибо что откликнулись на мою просьбу.Вот лог.Посмотрите пожалуста.Заранее огроменное спасибо.
=============================================================================
Intel(R) Server Platforms SE7520JR2 BMC RELEASE NOTES
=============================================================================
INTEL Enterprise Platform & Services Marketing
Intel Corporation
2111 N.E. 25th Avenue, Hillsboro, OR 97124 USA
=============================================================================
DATE: May 11, 2005
TO: Intel(R) server platform SE7520JR2 customers
SUBJECT: BMC(R) 0.47 Release Notes
=============================================================================
LEGAL INFORMATION
=============================================================================
Information in this document is provided in connection with Intel products.
No license, express or implied, by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability
whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating
to fitness for a particular purpose, merchantability, or infringement of any
patent, copyright or other intellectual property right. Intel Corporation may
have patents or pending patent applications, trademarks, copyrights, or other
intellectual property rights that relate to the presented subject matter.
The furnishing of documents and other materials and information does not
provide any license, express or implied, by estoppel or otherwise, to any
such patents, trademarks, copyrights, or other intellectual property rights.
Intel products are not intended for use in medical, life saving, or life
sustaining applications. Intel may make changes to specifications and product
descriptions at any time, without notice.
Intel is a registered trademark of Intel Corporation.
*Other names and brands are the property of their respective owners.
Copyright (c) 2005 Intel Corporation.
=============================================================================
ABOUT THIS RELEASE
=============================================================================
REVISION INFORMATION RETURNED BY GET DEVICE ID COMMAND:
Operational mode: v00.47
Flash update mode: v00.11
PIA data: v01.57
Manufacturer ID: 0x000157 (Intel)
Product ID: 0x0022 (SE7520JR2)
Checksum Information:
Operational Code
Region: 0x00030000 -> 0x000da7da
Checksum: 0xff11
Boot Block
Region: 0x00000000 -> 0x00003052
Checksum: 0x543a
=============================================================================
SYSTEM HARDWARE REQUIREMENTS/REVISIONS
=============================================================================
Intel(R) Management Module(IMM):
- Advanced Edition PBA C44973-405 or higher with BMC 0.23 or higher
installed.
- Professional Edition PBA C46194-301 or higher with BMC 0.23 or higher
installed.
Advanced Edition NIC board (GCM):
PBA C44941-201 (or later)
Server Board SE7520JR2 with the following PBA revisions (or higher):
C53659-301
C53660-404
C53661-601
C53662-503
=============================================================================
SYSTEM SOFTWARE REQUIREMENTS/REVISIONS
=============================================================================
- SE7520JR BIOS revision:
SE7520JR22.86B.P.05.00.0067.111820041003 (or later)
Any BIOS version prior to these will cause the BMC serial channel to not
function properly.
- SE7520JR2 FRU/SDR package:
JR-6.6.3 or later
- PC87431M mini-Baseboard Managment Controler (mBMC) from National Semiconductor:
Revision 2.40
- Firmware revisions on the Advanced Edition IMM card:
FPGA : rev 47 (or later)
EDID: rev 04
Any version prior to these will cause the Keyboard and mouse to become
non-functional.
The KVM viewer application will also not function properly with earlier
FPGA versions.
=============================================================================
IMPORTANT INSTALLATION NOTES
=============================================================================
- The following files are necessary to update the firmware:
Run.bat - Batch file used to update the firmware
7520JR47.hex - BMC 0.47 firmware hex file for the SE7520JR2 platform
FWPIAUpd.exe - DOS utility to program firmware hex file into the flash device
Prior versions of this utility will not work with this FW
Executing the fwpiaupd utility with your own command switches is unsupported
and may leave your baseboard in a non-operational state! Please use the
provided batch file to update the firmware.
Executing the batch file can be done from any media (Hard disk, USB disk-on-key,
shared network drive or floppy).
BMC 0.23 or later must be preinstalled.
If this is not the case, please update the IMM firmware to BMC 0.23 before
updating to this release.
The boot block has been changed with the BMC 0.31 release but it is not
required for this release. The batch file provided with this BMC package
does not update the boot block.
=============================================================================
INSTALLATION PROCEDURE
=============================================================================
- If this update is not being applied to BMC 0.23 or later, please first
update to 0.23.
- Copy the update files from this release package to the
media(Hard Drive, USB Disk-on-Key, Floppy...) that you wish to perform
the update from. Files include: run.bat, 7520JRxx.Hex, FWPIAUpd.exe,
- Execute the run.bat file to begin the firmware update process (if running
from the Software Update package, select update IMM Firmware option)
- Install the webserver EFS image revision 1.20 by either running upd_efs.bat
(if running from the Software Update package, select update EFS
Webserver option) or by uploading the efs_120.efs file using the web server
at URL http://xxx.xxx.xxx.xxx/!@efsUpdate. Replace the xxx.xxx.xxx.xxx
with the IP address used to configure the HTTP web server feature.
Please use the provided batch file as it contains the necessary -nopc
command line switch to FWPIAUPD.exe to successfully update the EFS area.
- Proceed to install the latest FRU/SDR package.
=============================================================================
KNOWN ISSUES/WORKAROUNDS
=============================================================================
- This and all future firmware releases will only support the fab -3xx
and later Professional and Advanced IMM.
Fab -2xx and prior modules are no longer supported!
See the SYSTEM HARDWARE REQUIREMENTS section above for details.
- Please clear the web browser cache if the web server feature was used prior
to BMC 0.37 as these cached pages will conflict with the pages generated
with versions after BMC 38 and EFS content rev 1.12.
The clearing of the web browser cache need only be done once.
=============================================================================
FEATURES ADDED With This Release
=============================================================================
BMC 0.47:
- None
=============================================================================
ISSUES FIXED With This Release
=============================================================================
BMC 0.47:
- DCS: 42200
Fix for #20373 created another issue (DR#42200) which has been resolved
- DCS: 42362
A memory leak in the web server has been resolved
- DCS: 19930
Self test errors with IMM Pro; changes that are made for the NCR SOL issue
*******************************
End of Current Release Notes
*******************************
===============================================================================
Pedigree of Changes
===============================================================================
BMC 0.46:
- DCS: 19438
Invalid Chassis information and Asset tag in the 'System Summary' page.
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19878
Gateway IP not getting reflected on the Summary page.
- DCS: 20076
False front panel temp lower critical events generated
- DCS: 20194
BMC TAM WDT alarms being cleared on power off
- DCS: 20373
When user creates a session with USER access, they can run any admin command
- DCS: 41879
Telnet/CLI: entering character after valid password "IPMI Session Error"
- DCS: 41920
No LAN functionality
- DCS: 42158
Watchdog timer test causes FRB timeout failure
- DCS: 76110
SE7520JR2 FRUSDR 6.6.1-Unexpected sel events for Temp Sensors,
Power Unit and Terminator
- DCS: 76154
POST Codes Not Driven by SIO on UUT3
BMC 0.45:
- DCS: 41857
(X) Power On/Off (warm reset) test hangs at Post C ode 13 or F8
- DCS: 42201
SR4850HWx CLI and SOL redirection loses connection frequently
BMC 0.44:
- DCS: 20125
KVM : Not able to see video redirection on SE7520JR2 Fab 503 board.
BMC 0.43:
- DCS: 20229
HTTP: 'Configuration' page fields could be set with 'User' privilege level.
BMC 0.42:
- DCS: 16837
FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes
- DCS: 20132
BMC fails self test err #8300
- DCS: 20140
Multiple email alerts are observed for single SEL entry
- DCS: 20194
BMC TAM WDT alarms being cleared on power off
- DCS: 20213
SCW: There are some errors observed at the end of SCW configuration.
- DCS: 20268
BMC stops responding very often - SE7520JR2
- DCS: 20307
Telnet: Invalid Password leads to BMC reset
BMC 0.41:
- DCS: 20132
BMC fails self test err #8300
- DCS: 20140
Multiple email alerts are observed for single SEL entry
- DCS: 20173
HTTP: Changing UsrUrl2 adds special characters
- DCS: 41534
SNMP: SNMPGet of SDR returns wrong values
- DCS: 41678
SMTP: Two emails received for the same event
BMC 0.40:
- DCS: 20078
BMC loses connectivity with KVM Viewer and launching ISM
- DCS: 20115
Updating or reading GCM FRU data fails nearly 30% of attempts
BMC 0.39:
- DCS: 19073
BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19376
KVM -Rebooting the system with KVM session active will lock the local Mouse
- DCS: 19844
CGI config byte reset to 00
- DCS: 19846
Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19827
Embedded CLI/SOL functionality is inconsistent and does not display correctly
- DCS: 19690
Web Server SEL View erratic
- DCS: 19377
KVM - Mouse control not returned back to Local server.
- DCS: 19891
SNMP Enable bit resets with power cycle
- DCS: 19454
SEL page does not display the entries.
- DCS: 19860
BMC38/Telnet: telnet and HTTP are not working when telnet port is changed
- DCS: 19861
PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19878
Network gateway IP not getting reflected on the Summary page
- DCS: 19879
Host name and Domain name should be clear on the Summary page.
- DCS: 19438
Invalid Chassis information and Asset tag in the "System Summary" page.
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 74756
FAN 5 and FAN 6 sensor numbers get swapped when IMM installed
- DCS: 19073
BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19846
Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19376
KVM -Rebooting the system with KVM session active will lock the local Mouse
- DCS: 19891
SNMP Enable bit resets with power cycle
- DCS: 19844
CGI config byte reset to 00
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19438
Invalid Chassis information and Asset tag in the ""System Summary"" page.
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19377
KVM - Mouse control not returned back to Local server.
- DCS: 19454
SEL page does not display the entries.
- DCS: 19690
Web Server SEL View erratic
- DCS: 19723
[x] Chassis intrussion not being logged in the SEL when opening the side cover
- DCS: 19878
Gateway IP not getting reflected on the Summary page.
- DCS: 19879
Host name and Domain name should be clear on the Summary page.
- DCS: 19860
BMC38/Telnet: telnet and HTTP are not working when telnet port is changed"
- DCS: 19861
PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19492
Email Alert is not working for 4 configurations
- DCS: 19585
LANDesk reports that mux is getting stuck in SYSTEM mode at BIOS POST end
- DCS: 19862
Alerts not generated for configured filters
- DCS: 19882
Error while accessing power control and SEL details in EFS web page
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 39766
SDR Clear does not cancel reservation
- DCS: 38098
SDR EraseTime timestamp Is Not Expected Time Value
- DCS: 74762
Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 76109
Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 19654
Issues with SEL view range in the web server
- DCS: 19840
Unnecessary characters appear on the left panel in Mozilla.
- DCS: 19882
Error while accessing power control and SEL details in EFS web page
- DCS: 19907
SOL: Accepted Character Count field is wrong.
- DCS: 19933
Issues with automatic refresh of SEL pages and default no. of entries.
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19956
Issues with ""Next"" button on the ""System Event log/SEL details"" page.
- DCS: 19958
Issues with ""Previous"" button on the ""System Event log"" page.
- DCS: 19959
Issues with ""Previous"" button on the ""SEL details"" page.
- DCS: 19969
embedded web server gives error if cli accessing BMC
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19943
SOL: SOL payloads jam indefinitely. Operation Status = 0x40
- DCS: 20013
HTTP : After working for around 2 - 2.5 hrs, Found issues with SEL details page
- DCS: 20038
DC power cycling is causing network stack to become unavailable.
- DCS: 40062
Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40063
Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40139
FSC system booting with 19+ SEL entries
- DCS: 41353
Telnet 'power -console' fails to show server screen
- DCS: 41588
SNMP fails to change ports
- DCS: 76000
FRB2 was not disabling the BSP when the SEL log was full
- DCS: 19912
System fails to boot with Riggins Base, P06 BIOS & IMM
- DCS: 74773
SE7520BD2 Fab7 board+ SC5300 base chassis+ IMM (professional version module),
server system can not power up and have 1-5-4-4 beep warning.
- DCS: 19888
Fix for data entry format in the IPMI command window.
It now accepts things like "20 18 1" as well as "20 18 01".
- DCS: 20041
Enabled the ability to write to the power unit and power supply FRU devices
BMC 0.38:
- DCS: 17571
HTTP web server about link causes error
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19454
SEL page does not display the entries
- DCS: 19475
ctWrong completion code returned for invalid commands in the web page
- DCS: 19558
[IMM] Status LED does not return to green from amber
- DCS: 19616
Fan status LED does not go out after hot swap fan is repaired
- DCS: 19628
BMC35/Telnet: Telnet is not working for any other port
- DCS: 19647
Incorrect data in the SEL record displayed in the SEL page
- DCS: 19654
Issues with SEL view range in the web server
- DCS: 19659
Wrong "Current power state" shown on the "Power Control" page
- DCS: 19678
Embedded web server "Help" link is broken
- DCS: 19679
Unexpected character on web server summary page
- DCS: 19682
Dislplay IMM GCM NIC gateway and subnet mask on summary page
- DCS: 19690
Web Server SEL View erratic
- DCS: 19737
Unable to telnet for user1 when password is reset
- DCS: 19801
Event receiver not set correctly in SATA HSBP after AC cycle
- DCS: 19824
Inconsistent mouse and keyboard control on KVM
- DCS: 19825
Power cycling on can cause the BMC to not allow further connections
- DCS: 19826
Logging into embedded CLI while KVM ena bled causes BMC reset
- DCS: 19828
Embedded CLI Banner still reads Sahalee BMC Embedded Telnet
- DCS: 19833
Updating NIC configuration during Telnet Session stops LAN interface
- DCS: 19836
Sessions and stress test issues with the web server
BMC 0.37:
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19439
No data available in the product area of the web page.
- DCS: 19452
SEL page does not display the entries.
- DCS: 19497
Help pages missing in the Embedded web server.
- DCS: 19534
EFS Updates failing
- DCS: 19628
BMC35/Telnet: Telnet is not working for any other port
- DCS: 19647
Incorrect data in the SEL record displayed in the SEL page.
- DCS: 19654
Issues with SEL view range in the web server.
- DCS: 19670
/!@efsUpdate page can be accessed/executed by any privilege level.
- DCS: 19677
"About" box for embedded Web Server copyright date
- DCS: 19678
Embedded web server "Help" link is broken
- DCS: 19679
Unexpected character on web server summary page
- DCS: 19680
Embedded Web Server has ( ) behind DIMMS, etc
- DCS: 19681
Remove "product" from web server summary page
- DCS: 19683
Web Server failure needs to be in Red
- DCS: 19684
Web Server summary page needs to show "RPM"
- DCS: 19690
Web Server SEL View erratic
- DCS: 19732
HTTP does not work for any port other than 80
- DCS: None
Sensors that are valid only while DC is on were being scanned
while DC was off.
- DCS: None
Separated the PCI HP module set for SR4850HWx as these were conflicting with
the SE7520AF2 PCI hot plug sensor enumerations.
- DCS: 40239
Added support for SR4850HWx in the platform mismatch command.
BMC 0.36
- DCS: 39809
Added new signals in MCH driver
- DCS: None
Web server enhancements from TME/PME review feedback
- DCS: None
Moved creation of new command tables to external RAM due to running out
of internal RAM.
BMC 0.35
- DCS: 19444
BMC32 Clearlog -state command in Telnet is not behaving as expected
- DCS: 19468
BMC32/Telnet: displaylog is not working with "-s" option
- DCS: 19488
BMC Prochot monitoring by BMC not reliable
- DCS: 19482
Could not connect to the web server in SE7520JR2 BMC 33..
- DCS: None
Fix for mouse and keyboard getting disabled during system reboot or reset.
- DCS: 19535
Front Panel reset button not getting locked in Sleep S1state
- DCS: 19493
BMC33/Telnet: telnet is not working with BMC33
BMC 0.34
- DCS: None
All advanced IMM features to not work with BMC 0.33
- DCS: 19530
Get HTTP Configuration Parameters-- Parameter Revision is not 0x11
- DCS: 19485
BMC to emulate keyboard / mouse correctly on Win2003
- DCS: 19494
Key Board Gets Disabled on Win2000
- DCS: 39476
Serial over LAN recieved unexpected successful response
BMC 0.33
- DCS: None
HTTP web server fixes
- DCS: 17503
Get SNMP Config Params command returns bad completion code
- DCS: 39454
SMI timeout does not work
- DCS: 39489
OEM1 bit is un-settable
- DCS: None
KVM fixes
- DCS: 18215
Init Agent fails to initialize the sensor thresholds
- DCS: 16670
HTTP Power Webpage, timestamp needs to be updated
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
BMC 0.32
- DCS: 17950
[IMM] Boot Initator info Block seemingly not validated
- DCS: 19398
PDB failure status not logged by BMC
- DCS: 15895, 16213, 16597, 16840, 17179, 18805, 19246, and 19321
Miscellaneous HTTP web server fixes
BMC 0.31
- DCS: 16325
EMP is not available for 10 seconds after DC ON
- DCS: 18410
Communication failure in Terminal mode
- DCS: 19027
Failed to make direct serial connection (LSM)
- DCS: 19028
Failed to establish Serial Modem Connection (LSM)
- DCS: 19031
[IMM] SecureModeActive bit is not set by the Secure Mode KB signal.
- DCS: 19306
CRERR04 - during console redirection and EMP is enabled
- DCS: 19354
Enable Telco Alarm Manager feature in SE7520JR2 BMC (IMM)
- DCS: 19363
BMC 30:SMTP -Parameter Revision is not 0x11
- DCS: 19369
SMTP config parm#6, DNS override, inverted
- DCS: 75975
[J1-IMM] BMC did not lock the Power and Reset push-buttons when Secure Mode
signal is asserted.
- DCS: None
Add support to allow the SE7520JR2 BMC firmware to execute on a SHW4 server
BMC 0.30
- DCS: 15819
IPMI2.0 commands not implemented correctly.
- DCS: 16415
KVM - Get Video Status requires video data structure
- DCS: 16634
FW: Setting an SMTP configuration appears to set multiple configurations
- DCS: 16837
FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes
- DCS: 17186
Get Channel Payload Support responses the same output
- DCS: 17459
KVM - Set KVM Config. to set in progress results in invalid completion code
- DCS: 17460
KVM - issuing Set KVM Configuration to disable KVM does not work.
- DCS: 17501
KVM - Activate Payload not returning all required bytes
- DCS: 17502
KVM - Video Status incorrectly reported when powered off
- DCS: 17503
Get SNMP Config Params command returns bad completion code
- DCS: 17538
FW: Issues with Set SMTP Config Params command
- DCS: 17540
FW: Issues with Set/Get LAN Config Params cmd w/ parameter 0xc4
- DCS: 17773
KVM - No Video Data Received
- DCS: 17779
KVM - Video packets still sent after Payload Deactivated
- DCS: 17815
KVM - Invalid Mouse Type reported
- DCS: 17860
KVM - BMC Becomes unresponsive to LAN connection
- DCS: 17863
KVM - Capture Reference Frame has too much data in it
- DCS: 17865
KVM - System will not boot w/KVM session Active
- DCS: 17949
LAN: chan 3 MAC Addr not auto-populated
- DCS: 18387
[IMM] Front Panel LCP is not discovered.
- DCS: 18698
Status LED does not turn amber when there is a fault on the system
- DCS: 19169
Restart Cause command is not working as expected
- DCS: 19237
PCI Hot Plug sensors stuck in init update mode after exit FW-Xfer mode
- DCS: 19239
[IMM] IERR occured at AC power cycle test.
- DCS: 19267
BMC29:Power control fault beep codes are emitted when repeated power cycles are
- DCS: 19299
LAN Alerts with Alert strings are reported as malformed packets
- DCS: 19321
EFS format/content not finalized yet
- DCS: 19324
Mouse / Keyboard Not Initialized when OS booted during a KVM session
- DCS: 19326
FPGA Encryption Problematic - After 100 + packets video data length is invalid
BMC 0.29:
- DCS: 19155
BMC doesn't correctly transition to S1 sleep state
- DCS: 34955
To implement Memory board Front and rear temperature sensors
- DCS: None
Better handling of power loss & DC off events.
- DCS: 19139
Console Redirection Causes Firmware Progress Errors in LD
- DCS: 38307
System failed to log AC power failure during boot
- DCS: 19107
BMC 0.28 Encountered failure while verifying sensor initialization value.
- DCS: 18875
Online Firmware Update causes BMC to hang
- DCS: 19156
RQ_SyncSMBus command locking wrong bus
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 18215
Removed init agent changes that were causing other problems.
- DCS: 18936
[IMM] IERR event is always occur right after AC on
- DCS: 19135
mBMC update with IMM installed fails on SE7520AL2 and SE7520BD2
- DCS: 16483
BMC and SDR updates fail
- DCS: 75901
DC cycling failed with IMM cards installed (Procs go offline)
- DCS: 75907
Processors being Disabled after an OS Restart
- DCS: 75908
Problems Powering On after an OS Shutdown
- DCS: 75915
BMC25 is shutting down immediately after loading and disabling the processors
- DCS: 74593
BIOS B19~P03 versions cause UUT boot failed after several front panel power
cycling while IMM card installed.
- DCS: 74618
IMM fails in SE7520BD2 -601A SCSI
BMC 0.28:
- DCS: 18866 & 18867
Thermal Trips were calling power control code to power down system. This
functionality is handled directly by the hardware.
- DCS: None
Added new module selection for Memory Board
- DCS: None
Fans would sometimes indicate failure at DC on.
- DCS: 19066
PCI Hot Plug Sensors do not show up
- DCS: None
Power supplies from shutting down due to current spikes caused by fan speed
changing to quickly.
- DCS: None
Processors are getting enabled and disabled twice during FRB3 failures.
- DCS: None
ID LED on would get locked on when button is pushed during power state
transitions.
- DCS: 18883
OOB connection not working out of subnet
- DCS: 19054
Repeat issuance of CLI power actions causes IMM to stop responding
- DCS: 19056
Thermal Trips being seen during DC power cycle testing
- DCS: 19072
1-5-4-4- beep code
- DCS: 19083
CLI lockup on power commands with BMC A.27 engineering release
- DCS: 19084
BMC a.27 causing therm trip and IERR errors on SE7520BD2 and SE7520JR2
BMC 0.27:
- Only released as incremental developer drops to verify resolutions that are
in place with the BMC 0.28 release.
BMC 0.26:
- DCS: 19010
Self test error with LSM Linux Console
- DCS: 18875
Online Firmware Update causes BMC to hang
- DCS: 19056
Thermal Trips being seen during DC power cycle testing
- DCS: 19016
Temporary failure of boot
- DCS: 18215
Init Agent fails to initialize the sensor thresholds
- DCS: None
Added some kick start ramping, but then went to a fixed 50% kick start.
- DCS: 19066
PCI Hot Plug Sensors do not show up
- DCS: 38317
BMC release process not producing repeatable checksums
- DCS: None
Changed to notify waiting task if multiple loss of arbitration detected,
regardless of task state.
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 19019
Rapid, succesive activation of the Power button, hangs BMC
- DCS: 19054
Repeat issuance of CLI power actions causes IMM to stop responding
BMC 0.25:
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 18638
BMC22: OnlineUpdateOpenArea is returning 0x00 as CC when it should not return so
- DCS: None
Fix for LAN channels not working after an exit firmware transfer mode
- DCS: 18875
Online Firmware Update causes BMC to hang
BMC 0.24:
- DCS: None
Fixed a defect in the VERIFY macro
- DCS: None
Added support for using a manufacturing test SDR
- DCS: None
HW team reporting fan circuit FETs being blown due to LM93 PWM outputs being
driven while DC is off
- DCS: None
If the private store gets cleared both processors will come up as disabled
by FRB3 on the next boot
- DCS: 18208
[IMM] CF9 hard reset does not work
- DCS: None
mBMC Driver potential error fix
- DCS: None
HW folks have the nominal, boost & sleep values set to FCh in the SDRs
which is wrong.
- DCS: 18217 & 18551
Implement a bi-color system fault indicator
(follow-up: counter-act the mBMC’s clearing of the LEDs on DC power on)
- DCS: None
Added defines to nullify printf in release mode
- DCS: 18806
BMC generates Self Test Error/ Parity Error with LanDesk SOL console
- DCS: None
Added support for using a shipping, TDE Adv IMM and TDE Pro IMM SDR.
- DCS: 18217
The comment describing the mBMC color conversion value assumptions was incorrect
- DCS: None
Found a memory leak in mactconet.c
- DCS: None
mBMC Driver reduce number of retries
- DCS: 18461
HDD LED on front panel is red when IMM is installed
- DCS: None
Incorporate the latest FSC spreadsheet data into the LM93 register defaults
- DCS: None
Added support for handling the IPMI requests “Set ACPI Power State?
and “Get ACPI Power State?through the SMM channel.
- DCS: None
mBMC Driver parameter tweaking to increase performance
- DCS: 18866
[IMM] Thermal trip event is not logged in SEL
- DCS: 18867
[IMM] IERR event is not logged in SEL
- DCS: 18745
Fans do not contribute to the overall health of the system
- DCS: 18883
OOB connection not working out of subnet
- DCS: 18243
2nd CPU fails with frb3 during post
- DCS: 18802
BMC failing self test corrupts BIOS information
- DCS: 18854
SE7520AL2 BMC 23 - Resolve MAC hangs BMC
BMC 0.23:
- DCS: 16967
PET Traps were not getting detected
- DCS: 18548
[IMM] BMC failed BIOS self test after update to BMC version 21
- DCS: 18612
BMC does not retain OOB connectivity after installation of ISM on server
- DCS: 18217
Front Panel Bi-Color LED behaviour
- DCS: 18551
[IMM] Status LED is not changed at the critical event.
- DCS: 75827
[J1] Baseboard Management Controller Failed by Self Test command during POST
with Sahalee FW 0.21.
- DCS: 18549
LM93 OEM SDR would cause the BMC to hang
- DCS: 18595
FRUSDR version 6.2.1 Update failling with BIOS P01 and BMC 21
- DCS: None
Added encapsulating PACKED_xxx definitions around some packed structures.
- DCS: None
Refined the fan control for power ON and Hot swap kick Start;
Added checks to avoid C, NC Assertions during power ON&Reset;
Added the de-assertion Actions in the PIA for hot swap fans; Fans boost
in the particular domain on HS fan removal
Restored the default Nominal to half by handling the power on and HS kick
start in the fanctrl.c code
- DCS: None
New OEM command to restore the non-volatile configuration.
This command needs to be called by the utility when the platform mismatch
found during the FW update.
- DCS: None
SensAvgCreate() would allow illegal input data
- DCS: None
Baseboards with maximum DIMM capacity were causing systems to reset
during POST due to the FRB3 timer expiring.
- DCS: None
mBMC Driver message potential error fix
- DCS: None
Multiple stack overflow issues
- DCS: None
This check-in partially addresses clearing out bogus fan failures that are
persistently stored.
I have seen issues with moving my IMM between different platform types,
where ATTNID_OK has a different value.
=============================================================================
Intel(R) Server Platforms SE7520JR2 BMC RELEASE NOTES
=============================================================================
INTEL Enterprise Platform & Services Marketing
Intel Corporation
2111 N.E. 25th Avenue, Hillsboro, OR 97124 USA
=============================================================================
DATE: May 11, 2005
TO: Intel(R) server platform SE7520JR2 customers
SUBJECT: BMC(R) 0.47 Release Notes
=============================================================================
LEGAL INFORMATION
=============================================================================
Information in this document is provided in connection with Intel products.
No license, express or implied, by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Intel's
Terms and Conditions of Sale for such products, Intel assumes no liability
whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating
to fitness for a particular purpose, merchantability, or infringement of any
patent, copyright or other intellectual property right. Intel Corporation may
have patents or pending patent applications, trademarks, copyrights, or other
intellectual property rights that relate to the presented subject matter.
The furnishing of documents and other materials and information does not
provide any license, express or implied, by estoppel or otherwise, to any
such patents, trademarks, copyrights, or other intellectual property rights.
Intel products are not intended for use in medical, life saving, or life
sustaining applications. Intel may make changes to specifications and product
descriptions at any time, without notice.
Intel is a registered trademark of Intel Corporation.
*Other names and brands are the property of their respective owners.
Copyright (c) 2005 Intel Corporation.
=============================================================================
ABOUT THIS RELEASE
=============================================================================
REVISION INFORMATION RETURNED BY GET DEVICE ID COMMAND:
Operational mode: v00.47
Flash update mode: v00.11
PIA data: v01.57
Manufacturer ID: 0x000157 (Intel)
Product ID: 0x0022 (SE7520JR2)
Checksum Information:
Operational Code
Region: 0x00030000 -> 0x000da7da
Checksum: 0xff11
Boot Block
Region: 0x00000000 -> 0x00003052
Checksum: 0x543a
=============================================================================
SYSTEM HARDWARE REQUIREMENTS/REVISIONS
=============================================================================
Intel(R) Management Module(IMM):
- Advanced Edition PBA C44973-405 or higher with BMC 0.23 or higher
installed.
- Professional Edition PBA C46194-301 or higher with BMC 0.23 or higher
installed.
Advanced Edition NIC board (GCM):
PBA C44941-201 (or later)
Server Board SE7520JR2 with the following PBA revisions (or higher):
C53659-301
C53660-404
C53661-601
C53662-503
=============================================================================
SYSTEM SOFTWARE REQUIREMENTS/REVISIONS
=============================================================================
- SE7520JR BIOS revision:
SE7520JR22.86B.P.05.00.0067.111820041003 (or later)
Any BIOS version prior to these will cause the BMC serial channel to not
function properly.
- SE7520JR2 FRU/SDR package:
JR-6.6.3 or later
- PC87431M mini-Baseboard Managment Controler (mBMC) from National Semiconductor:
Revision 2.40
- Firmware revisions on the Advanced Edition IMM card:
FPGA : rev 47 (or later)
EDID: rev 04
Any version prior to these will cause the Keyboard and mouse to become
non-functional.
The KVM viewer application will also not function properly with earlier
FPGA versions.
=============================================================================
IMPORTANT INSTALLATION NOTES
=============================================================================
- The following files are necessary to update the firmware:
Run.bat - Batch file used to update the firmware
7520JR47.hex - BMC 0.47 firmware hex file for the SE7520JR2 platform
FWPIAUpd.exe - DOS utility to program firmware hex file into the flash device
Prior versions of this utility will not work with this FW
Executing the fwpiaupd utility with your own command switches is unsupported
and may leave your baseboard in a non-operational state! Please use the
provided batch file to update the firmware.
Executing the batch file can be done from any media (Hard disk, USB disk-on-key,
shared network drive or floppy).
BMC 0.23 or later must be preinstalled.
If this is not the case, please update the IMM firmware to BMC 0.23 before
updating to this release.
The boot block has been changed with the BMC 0.31 release but it is not
required for this release. The batch file provided with this BMC package
does not update the boot block.
=============================================================================
INSTALLATION PROCEDURE
=============================================================================
- If this update is not being applied to BMC 0.23 or later, please first
update to 0.23.
- Copy the update files from this release package to the
media(Hard Drive, USB Disk-on-Key, Floppy...) that you wish to perform
the update from. Files include: run.bat, 7520JRxx.Hex, FWPIAUpd.exe,
- Execute the run.bat file to begin the firmware update process (if running
from the Software Update package, select update IMM Firmware option)
- Install the webserver EFS image revision 1.20 by either running upd_efs.bat
(if running from the Software Update package, select update EFS
Webserver option) or by uploading the efs_120.efs file using the web server
at URL http://xxx.xxx.xxx.xxx/!@efsUpdate. Replace the xxx.xxx.xxx.xxx
with the IP address used to configure the HTTP web server feature.
Please use the provided batch file as it contains the necessary -nopc
command line switch to FWPIAUPD.exe to successfully update the EFS area.
- Proceed to install the latest FRU/SDR package.
=============================================================================
KNOWN ISSUES/WORKAROUNDS
=============================================================================
- This and all future firmware releases will only support the fab -3xx
and later Professional and Advanced IMM.
Fab -2xx and prior modules are no longer supported!
See the SYSTEM HARDWARE REQUIREMENTS section above for details.
- Please clear the web browser cache if the web server feature was used prior
to BMC 0.37 as these cached pages will conflict with the pages generated
with versions after BMC 38 and EFS content rev 1.12.
The clearing of the web browser cache need only be done once.
=============================================================================
FEATURES ADDED With This Release
=============================================================================
BMC 0.47:
- None
=============================================================================
ISSUES FIXED With This Release
=============================================================================
BMC 0.47:
- DCS: 42200
Fix for #20373 created another issue (DR#42200) which has been resolved
- DCS: 42362
A memory leak in the web server has been resolved
- DCS: 19930
Self test errors with IMM Pro; changes that are made for the NCR SOL issue
*******************************
End of Current Release Notes
*******************************
===============================================================================
Pedigree of Changes
===============================================================================
BMC 0.46:
- DCS: 19438
Invalid Chassis information and Asset tag in the 'System Summary' page.
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19878
Gateway IP not getting reflected on the Summary page.
- DCS: 20076
False front panel temp lower critical events generated
- DCS: 20194
BMC TAM WDT alarms being cleared on power off
- DCS: 20373
When user creates a session with USER access, they can run any admin command
- DCS: 41879
Telnet/CLI: entering character after valid password "IPMI Session Error"
- DCS: 41920
No LAN functionality
- DCS: 42158
Watchdog timer test causes FRB timeout failure
- DCS: 76110
SE7520JR2 FRUSDR 6.6.1-Unexpected sel events for Temp Sensors,
Power Unit and Terminator
- DCS: 76154
POST Codes Not Driven by SIO on UUT3
BMC 0.45:
- DCS: 41857
(X) Power On/Off (warm reset) test hangs at Post C ode 13 or F8
- DCS: 42201
SR4850HWx CLI and SOL redirection loses connection frequently
BMC 0.44:
- DCS: 20125
KVM : Not able to see video redirection on SE7520JR2 Fab 503 board.
BMC 0.43:
- DCS: 20229
HTTP: 'Configuration' page fields could be set with 'User' privilege level.
BMC 0.42:
- DCS: 16837
FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes
- DCS: 20132
BMC fails self test err #8300
- DCS: 20140
Multiple email alerts are observed for single SEL entry
- DCS: 20194
BMC TAM WDT alarms being cleared on power off
- DCS: 20213
SCW: There are some errors observed at the end of SCW configuration.
- DCS: 20268
BMC stops responding very often - SE7520JR2
- DCS: 20307
Telnet: Invalid Password leads to BMC reset
BMC 0.41:
- DCS: 20132
BMC fails self test err #8300
- DCS: 20140
Multiple email alerts are observed for single SEL entry
- DCS: 20173
HTTP: Changing UsrUrl2 adds special characters
- DCS: 41534
SNMP: SNMPGet of SDR returns wrong values
- DCS: 41678
SMTP: Two emails received for the same event
BMC 0.40:
- DCS: 20078
BMC loses connectivity with KVM Viewer and launching ISM
- DCS: 20115
Updating or reading GCM FRU data fails nearly 30% of attempts
BMC 0.39:
- DCS: 19073
BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19376
KVM -Rebooting the system with KVM session active will lock the local Mouse
- DCS: 19844
CGI config byte reset to 00
- DCS: 19846
Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19827
Embedded CLI/SOL functionality is inconsistent and does not display correctly
- DCS: 19690
Web Server SEL View erratic
- DCS: 19377
KVM - Mouse control not returned back to Local server.
- DCS: 19891
SNMP Enable bit resets with power cycle
- DCS: 19454
SEL page does not display the entries.
- DCS: 19860
BMC38/Telnet: telnet and HTTP are not working when telnet port is changed
- DCS: 19861
PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19878
Network gateway IP not getting reflected on the Summary page
- DCS: 19879
Host name and Domain name should be clear on the Summary page.
- DCS: 19438
Invalid Chassis information and Asset tag in the "System Summary" page.
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 74756
FAN 5 and FAN 6 sensor numbers get swapped when IMM installed
- DCS: 19073
BMC not responding going across sub-nets for Adv IMM card
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19846
Web server hangs on clicking ""Clear SEL"" on the page.
- DCS: 19376
KVM -Rebooting the system with KVM session active will lock the local Mouse
- DCS: 19891
SNMP Enable bit resets with power cycle
- DCS: 19844
CGI config byte reset to 00
- DCS: 19850
Host and domain name updates not successful.
- DCS: 19438
Invalid Chassis information and Asset tag in the ""System Summary"" page.
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19377
KVM - Mouse control not returned back to Local server.
- DCS: 19454
SEL page does not display the entries.
- DCS: 19690
Web Server SEL View erratic
- DCS: 19723
[x] Chassis intrussion not being logged in the SEL when opening the side cover
- DCS: 19878
Gateway IP not getting reflected on the Summary page.
- DCS: 19879
Host name and Domain name should be clear on the Summary page.
- DCS: 19860
BMC38/Telnet: telnet and HTTP are not working when telnet port is changed"
- DCS: 19861
PS1 Status on the Summary page shows ""Inst"" for ""Installed"".
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19492
Email Alert is not working for 4 configurations
- DCS: 19585
LANDesk reports that mux is getting stuck in SYSTEM mode at BIOS POST end
- DCS: 19862
Alerts not generated for configured filters
- DCS: 19882
Error while accessing power control and SEL details in EFS web page
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 39766
SDR Clear does not cancel reservation
- DCS: 38098
SDR EraseTime timestamp Is Not Expected Time Value
- DCS: 74762
Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 76109
Sometimes BMC will disable event messages from threshold type sensors after A/C off then on
- DCS: 19654
Issues with SEL view range in the web server
- DCS: 19840
Unnecessary characters appear on the left panel in Mozilla.
- DCS: 19882
Error while accessing power control and SEL details in EFS web page
- DCS: 19907
SOL: Accepted Character Count field is wrong.
- DCS: 19933
Issues with automatic refresh of SEL pages and default no. of entries.
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19956
Issues with ""Next"" button on the ""System Event log/SEL details"" page.
- DCS: 19958
Issues with ""Previous"" button on the ""System Event log"" page.
- DCS: 19959
Issues with ""Previous"" button on the ""SEL details"" page.
- DCS: 19969
embedded web server gives error if cli accessing BMC
- DCS: 19880
BMC38/Telnet: login propmt should not come when all 4 telnet sessions are active
- DCS: 19881
BMC38/Telnet: BMC has become busy(CC is 0xC0), not coming out of this state
- DCS: 19937
SEL pages not working after few hours of loading BMC 1.39, EFS 1.13
- DCS: 19943
SOL: SOL payloads jam indefinitely. Operation Status = 0x40
- DCS: 20013
HTTP : After working for around 2 - 2.5 hrs, Found issues with SEL details page
- DCS: 20038
DC power cycling is causing network stack to become unavailable.
- DCS: 40062
Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40063
Cipher Suite Id 7 & 8 failed to establish a session
- DCS: 40139
FSC system booting with 19+ SEL entries
- DCS: 41353
Telnet 'power -console' fails to show server screen
- DCS: 41588
SNMP fails to change ports
- DCS: 76000
FRB2 was not disabling the BSP when the SEL log was full
- DCS: 19912
System fails to boot with Riggins Base, P06 BIOS & IMM
- DCS: 74773
SE7520BD2 Fab7 board+ SC5300 base chassis+ IMM (professional version module),
server system can not power up and have 1-5-4-4 beep warning.
- DCS: 19888
Fix for data entry format in the IPMI command window.
It now accepts things like "20 18 1" as well as "20 18 01".
- DCS: 20041
Enabled the ability to write to the power unit and power supply FRU devices
BMC 0.38:
- DCS: 17571
HTTP web server about link causes error
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19454
SEL page does not display the entries
- DCS: 19475
ctWrong completion code returned for invalid commands in the web page
- DCS: 19558
[IMM] Status LED does not return to green from amber
- DCS: 19616
Fan status LED does not go out after hot swap fan is repaired
- DCS: 19628
BMC35/Telnet: Telnet is not working for any other port
- DCS: 19647
Incorrect data in the SEL record displayed in the SEL page
- DCS: 19654
Issues with SEL view range in the web server
- DCS: 19659
Wrong "Current power state" shown on the "Power Control" page
- DCS: 19678
Embedded web server "Help" link is broken
- DCS: 19679
Unexpected character on web server summary page
- DCS: 19682
Dislplay IMM GCM NIC gateway and subnet mask on summary page
- DCS: 19690
Web Server SEL View erratic
- DCS: 19737
Unable to telnet for user1 when password is reset
- DCS: 19801
Event receiver not set correctly in SATA HSBP after AC cycle
- DCS: 19824
Inconsistent mouse and keyboard control on KVM
- DCS: 19825
Power cycling on can cause the BMC to not allow further connections
- DCS: 19826
Logging into embedded CLI while KVM ena bled causes BMC reset
- DCS: 19828
Embedded CLI Banner still reads Sahalee BMC Embedded Telnet
- DCS: 19833
Updating NIC configuration during Telnet Session stops LAN interface
- DCS: 19836
Sessions and stress test issues with the web server
BMC 0.37:
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
- DCS: 19439
No data available in the product area of the web page.
- DCS: 19452
SEL page does not display the entries.
- DCS: 19497
Help pages missing in the Embedded web server.
- DCS: 19534
EFS Updates failing
- DCS: 19628
BMC35/Telnet: Telnet is not working for any other port
- DCS: 19647
Incorrect data in the SEL record displayed in the SEL page.
- DCS: 19654
Issues with SEL view range in the web server.
- DCS: 19670
/!@efsUpdate page can be accessed/executed by any privilege level.
- DCS: 19677
"About" box for embedded Web Server copyright date
- DCS: 19678
Embedded web server "Help" link is broken
- DCS: 19679
Unexpected character on web server summary page
- DCS: 19680
Embedded Web Server has ( ) behind DIMMS, etc
- DCS: 19681
Remove "product" from web server summary page
- DCS: 19683
Web Server failure needs to be in Red
- DCS: 19684
Web Server summary page needs to show "RPM"
- DCS: 19690
Web Server SEL View erratic
- DCS: 19732
HTTP does not work for any port other than 80
- DCS: None
Sensors that are valid only while DC is on were being scanned
while DC was off.
- DCS: None
Separated the PCI HP module set for SR4850HWx as these were conflicting with
the SE7520AF2 PCI hot plug sensor enumerations.
- DCS: 40239
Added support for SR4850HWx in the platform mismatch command.
BMC 0.36
- DCS: 39809
Added new signals in MCH driver
- DCS: None
Web server enhancements from TME/PME review feedback
- DCS: None
Moved creation of new command tables to external RAM due to running out
of internal RAM.
BMC 0.35
- DCS: 19444
BMC32 Clearlog -state command in Telnet is not behaving as expected
- DCS: 19468
BMC32/Telnet: displaylog is not working with "-s" option
- DCS: 19488
BMC Prochot monitoring by BMC not reliable
- DCS: 19482
Could not connect to the web server in SE7520JR2 BMC 33..
- DCS: None
Fix for mouse and keyboard getting disabled during system reboot or reset.
- DCS: 19535
Front Panel reset button not getting locked in Sleep S1state
- DCS: 19493
BMC33/Telnet: telnet is not working with BMC33
BMC 0.34
- DCS: None
All advanced IMM features to not work with BMC 0.33
- DCS: 19530
Get HTTP Configuration Parameters-- Parameter Revision is not 0x11
- DCS: 19485
BMC to emulate keyboard / mouse correctly on Win2003
- DCS: 19494
Key Board Gets Disabled on Win2000
- DCS: 39476
Serial over LAN recieved unexpected successful response
BMC 0.33
- DCS: None
HTTP web server fixes
- DCS: 17503
Get SNMP Config Params command returns bad completion code
- DCS: 39454
SMI timeout does not work
- DCS: 39489
OEM1 bit is un-settable
- DCS: None
KVM fixes
- DCS: 18215
Init Agent fails to initialize the sensor thresholds
- DCS: 16670
HTTP Power Webpage, timestamp needs to be updated
- DCS: 19402
SEL page in EFS content rev 1.6 has errors
BMC 0.32
- DCS: 17950
[IMM] Boot Initator info Block seemingly not validated
- DCS: 19398
PDB failure status not logged by BMC
- DCS: 15895, 16213, 16597, 16840, 17179, 18805, 19246, and 19321
Miscellaneous HTTP web server fixes
BMC 0.31
- DCS: 16325
EMP is not available for 10 seconds after DC ON
- DCS: 18410
Communication failure in Terminal mode
- DCS: 19027
Failed to make direct serial connection (LSM)
- DCS: 19028
Failed to establish Serial Modem Connection (LSM)
- DCS: 19031
[IMM] SecureModeActive bit is not set by the Secure Mode KB signal.
- DCS: 19306
CRERR04 - during console redirection and EMP is enabled
- DCS: 19354
Enable Telco Alarm Manager feature in SE7520JR2 BMC (IMM)
- DCS: 19363
BMC 30:SMTP -Parameter Revision is not 0x11
- DCS: 19369
SMTP config parm#6, DNS override, inverted
- DCS: 75975
[J1-IMM] BMC did not lock the Power and Reset push-buttons when Secure Mode
signal is asserted.
- DCS: None
Add support to allow the SE7520JR2 BMC firmware to execute on a SHW4 server
BMC 0.30
- DCS: 15819
IPMI2.0 commands not implemented correctly.
- DCS: 16415
KVM - Get Video Status requires video data structure
- DCS: 16634
FW: Setting an SMTP configuration appears to set multiple configurations
- DCS: 16837
FW: User Feature cmd for HTTP/S enables returns incorrect # of data bytes
- DCS: 17186
Get Channel Payload Support responses the same output
- DCS: 17459
KVM - Set KVM Config. to set in progress results in invalid completion code
- DCS: 17460
KVM - issuing Set KVM Configuration to disable KVM does not work.
- DCS: 17501
KVM - Activate Payload not returning all required bytes
- DCS: 17502
KVM - Video Status incorrectly reported when powered off
- DCS: 17503
Get SNMP Config Params command returns bad completion code
- DCS: 17538
FW: Issues with Set SMTP Config Params command
- DCS: 17540
FW: Issues with Set/Get LAN Config Params cmd w/ parameter 0xc4
- DCS: 17773
KVM - No Video Data Received
- DCS: 17779
KVM - Video packets still sent after Payload Deactivated
- DCS: 17815
KVM - Invalid Mouse Type reported
- DCS: 17860
KVM - BMC Becomes unresponsive to LAN connection
- DCS: 17863
KVM - Capture Reference Frame has too much data in it
- DCS: 17865
KVM - System will not boot w/KVM session Active
- DCS: 17949
LAN: chan 3 MAC Addr not auto-populated
- DCS: 18387
[IMM] Front Panel LCP is not discovered.
- DCS: 18698
Status LED does not turn amber when there is a fault on the system
- DCS: 19169
Restart Cause command is not working as expected
- DCS: 19237
PCI Hot Plug sensors stuck in init update mode after exit FW-Xfer mode
- DCS: 19239
[IMM] IERR occured at AC power cycle test.
- DCS: 19267
BMC29:Power control fault beep codes are emitted when repeated power cycles are
- DCS: 19299
LAN Alerts with Alert strings are reported as malformed packets
- DCS: 19321
EFS format/content not finalized yet
- DCS: 19324
Mouse / Keyboard Not Initialized when OS booted during a KVM session
- DCS: 19326
FPGA Encryption Problematic - After 100 + packets video data length is invalid
BMC 0.29:
- DCS: 19155
BMC doesn't correctly transition to S1 sleep state
- DCS: 34955
To implement Memory board Front and rear temperature sensors
- DCS: None
Better handling of power loss & DC off events.
- DCS: 19139
Console Redirection Causes Firmware Progress Errors in LD
- DCS: 38307
System failed to log AC power failure during boot
- DCS: 19107
BMC 0.28 Encountered failure while verifying sensor initialization value.
- DCS: 18875
Online Firmware Update causes BMC to hang
- DCS: 19156
RQ_SyncSMBus command locking wrong bus
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 18215
Removed init agent changes that were causing other problems.
- DCS: 18936
[IMM] IERR event is always occur right after AC on
- DCS: 19135
mBMC update with IMM installed fails on SE7520AL2 and SE7520BD2
- DCS: 16483
BMC and SDR updates fail
- DCS: 75901
DC cycling failed with IMM cards installed (Procs go offline)
- DCS: 75907
Processors being Disabled after an OS Restart
- DCS: 75908
Problems Powering On after an OS Shutdown
- DCS: 75915
BMC25 is shutting down immediately after loading and disabling the processors
- DCS: 74593
BIOS B19~P03 versions cause UUT boot failed after several front panel power
cycling while IMM card installed.
- DCS: 74618
IMM fails in SE7520BD2 -601A SCSI
BMC 0.28:
- DCS: 18866 & 18867
Thermal Trips were calling power control code to power down system. This
functionality is handled directly by the hardware.
- DCS: None
Added new module selection for Memory Board
- DCS: None
Fans would sometimes indicate failure at DC on.
- DCS: 19066
PCI Hot Plug Sensors do not show up
- DCS: None
Power supplies from shutting down due to current spikes caused by fan speed
changing to quickly.
- DCS: None
Processors are getting enabled and disabled twice during FRB3 failures.
- DCS: None
ID LED on would get locked on when button is pushed during power state
transitions.
- DCS: 18883
OOB connection not working out of subnet
- DCS: 19054
Repeat issuance of CLI power actions causes IMM to stop responding
- DCS: 19056
Thermal Trips being seen during DC power cycle testing
- DCS: 19072
1-5-4-4- beep code
- DCS: 19083
CLI lockup on power commands with BMC A.27 engineering release
- DCS: 19084
BMC a.27 causing therm trip and IERR errors on SE7520BD2 and SE7520JR2
BMC 0.27:
- Only released as incremental developer drops to verify resolutions that are
in place with the BMC 0.28 release.
BMC 0.26:
- DCS: 19010
Self test error with LSM Linux Console
- DCS: 18875
Online Firmware Update causes BMC to hang
- DCS: 19056
Thermal Trips being seen during DC power cycle testing
- DCS: 19016
Temporary failure of boot
- DCS: 18215
Init Agent fails to initialize the sensor thresholds
- DCS: None
Added some kick start ramping, but then went to a fixed 50% kick start.
- DCS: 19066
PCI Hot Plug Sensors do not show up
- DCS: 38317
BMC release process not producing repeatable checksums
- DCS: None
Changed to notify waiting task if multiple loss of arbitration detected,
regardless of task state.
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 19019
Rapid, succesive activation of the Power button, hangs BMC
- DCS: 19054
Repeat issuance of CLI power actions causes IMM to stop responding
BMC 0.25:
- DCS: 18963
PS_PWR_GD ISR is not being enabled occasionally
- DCS: 18638
BMC22: OnlineUpdateOpenArea is returning 0x00 as CC when it should not return so
- DCS: None
Fix for LAN channels not working after an exit firmware transfer mode
- DCS: 18875
Online Firmware Update causes BMC to hang
BMC 0.24:
- DCS: None
Fixed a defect in the VERIFY macro
- DCS: None
Added support for using a manufacturing test SDR
- DCS: None
HW team reporting fan circuit FETs being blown due to LM93 PWM outputs being
driven while DC is off
- DCS: None
If the private store gets cleared both processors will come up as disabled
by FRB3 on the next boot
- DCS: 18208
[IMM] CF9 hard reset does not work
- DCS: None
mBMC Driver potential error fix
- DCS: None
HW folks have the nominal, boost & sleep values set to FCh in the SDRs
which is wrong.
- DCS: 18217 & 18551
Implement a bi-color system fault indicator
(follow-up: counter-act the mBMC’s clearing of the LEDs on DC power on)
- DCS: None
Added defines to nullify printf in release mode
- DCS: 18806
BMC generates Self Test Error/ Parity Error with LanDesk SOL console
- DCS: None
Added support for using a shipping, TDE Adv IMM and TDE Pro IMM SDR.
- DCS: 18217
The comment describing the mBMC color conversion value assumptions was incorrect
- DCS: None
Found a memory leak in mactconet.c
- DCS: None
mBMC Driver reduce number of retries
- DCS: 18461
HDD LED on front panel is red when IMM is installed
- DCS: None
Incorporate the latest FSC spreadsheet data into the LM93 register defaults
- DCS: None
Added support for handling the IPMI requests “Set ACPI Power State?
and “Get ACPI Power State?through the SMM channel.
- DCS: None
mBMC Driver parameter tweaking to increase performance
- DCS: 18866
[IMM] Thermal trip event is not logged in SEL
- DCS: 18867
[IMM] IERR event is not logged in SEL
- DCS: 18745
Fans do not contribute to the overall health of the system
- DCS: 18883
OOB connection not working out of subnet
- DCS: 18243
2nd CPU fails with frb3 during post
- DCS: 18802
BMC failing self test corrupts BIOS information
- DCS: 18854
SE7520AL2 BMC 23 - Resolve MAC hangs BMC
BMC 0.23:
- DCS: 16967
PET Traps were not getting detected
- DCS: 18548
[IMM] BMC failed BIOS self test after update to BMC version 21
- DCS: 18612
BMC does not retain OOB connectivity after installation of ISM on server
- DCS: 18217
Front Panel Bi-Color LED behaviour
- DCS: 18551
[IMM] Status LED is not changed at the critical event.
- DCS: 75827
[J1] Baseboard Management Controller Failed by Self Test command during POST
with Sahalee FW 0.21.
- DCS: 18549
LM93 OEM SDR would cause the BMC to hang
- DCS: 18595
FRUSDR version 6.2.1 Update failling with BIOS P01 and BMC 21
- DCS: None
Added encapsulating PACKED_xxx definitions around some packed structures.
- DCS: None
Refined the fan control for power ON and Hot swap kick Start;
Added checks to avoid C, NC Assertions during power ON&Reset;
Added the de-assertion Actions in the PIA for hot swap fans; Fans boost
in the particular domain on HS fan removal
Restored the default Nominal to half by handling the power on and HS kick
start in the fanctrl.c code
- DCS: None
New OEM command to restore the non-volatile configuration.
This command needs to be called by the utility when the platform mismatch
found during the FW update.
- DCS: None
SensAvgCreate() would allow illegal input data
- DCS: None
Baseboards with maximum DIMM capacity were causing systems to reset
during POST due to the FRB3 timer expiring.
- DCS: None
mBMC Driver message potential error fix
- DCS: None
Multiple stack overflow issues
- DCS: None
This check-in partially addresses clearing out bogus fan failures that are
persistently stored.
I have seen issues with moving my IMM between different platform types,
where ATTNID_OK has a different value.
- Kirill Tkachev
- Advanced member
- Сообщения: 481
- Зарегистрирован: 08 июл 2004, 13:37
- Откуда: Saint-Petersburg
- Контактная информация:
Это немного не тот лог.
Скачайте утилиту SEL Viewer
http://downloadcenter.intel.com/scripts ... nldID=7470
И сохраните SEL в файл.
Скачайте утилиту SEL Viewer
http://downloadcenter.intel.com/scripts ... nldID=7470
И сохраните SEL в файл.
Кинул на at@trinity.su.Посмотрите.
Кто сейчас на конференции
Сейчас этот форум просматривают: Bing [Bot] и 12 гостей